[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: CDC Layout
Hi Beni -
the first concern is my fault, I attached the wrong versions of the
endplate files to the email. The correct ones do agree at all layers.
I will modify the code to provide the stereo angles , and add sig. digits
to the first table, and then recommunicate the information.
Curtis
On Mon March 2 2009, Beni Zihlmann wrote:
> Hi Yves,
> thanks for the clarification. I have one more question and one request:
> Question: the central radius in the first table agrees with the central
> radius
> of the second and third table only for the first 4
> layers. After that
> there is a difference between the values of column 3
> (radius center)
> of the first table and column 4 of the second and third
> table (r_c).
> If this is correct then I do not understand what r_c means.
>
> Request: could you also add to table two and three the actual values for
> the stereo angles
> in either rad or degree. When calculating the angles
> using the values in the table
> one gets rounding errors and they are significant when
> taking an arcus tangens
> from a ratio of already rounded values.
>
> cheers,
> Beni
>
>
> > Hi Beni,
> >
> > Straw outer radius (OR) = 0.79375cm OD = 1.5875 cm
> > Straw outer radius + 75um tolerance = 0.80125 or OD = 1.6025
> >
> > The program uses the OR + tolerance as actual OR to position the
> > straws. That is why is sais global radius = 0.80125 cm. It is the
> > radius it starts with. The program will vary the tolerence on the
> > radius from 75-100 um to minimize the layer radius.
> >
> > Cheers,
> > Yves
> >
> >
> >
> >
> >
> >
> > /--------------------------------
> > / Yves Van Haarlem
> > _--~~--_ /
> > /~/_| |_\~\ / Carnegie Mellon University
> > |____________| / Department of Physics
> > |[][][][][][]|:= / Wean Hall room 8404
> > __| __ |__ \ Pittsburgh, PA 15213
> > | ||. | == | | \ USA
> > (| ||__| == | |) \
> > | |[] [] == | | \ Tel.: +1 412 268-6949
> > | |____________| | \ +1 412 641-9252
> > /__\ /__\ \ Fax.: +1 412 681-0648
> > ~~ ~~ \-----------------------------------
> >
> > On Sun, 1 Mar 2009, Beni Zihlmann wrote:
> >
> >> Hi Curtis,
> >> I see here one inconsistency.
> >> at point 1) the OD of a straw is given as 1.5875 cm but below
> >> in Global Information the Tube radius is given as 0.801250 cm ??
> >>
> >> cheers,
> >> Beni
> >>> Hi Everyone -
> >>>
> >>> based on the dicsussions that we held this morning, Yves and I
> >>> changed the layout rules for wire spacing. We now do the following:
> >>>
> >>> 1) Nominal Tube OD is 1.5875 cm
> >>> 2) We require a spacing of at least 150 microns and no more than
> >>> 200 microns between straws.
> >>> 3) We allowed layer 1 to move in from 10.95cm to 10.69 cm (wire
> >>> position) --- 2.6 mm
> >>>
> >>> We can now get 28 layers with 3500 wires in the allocated space. The
> >>> wire position of the 28'th layer is at 54.488cm.
> >>>
> >>> If we loosen rule (2) to be 150 to 225, we can leave layer 1 at 10.95
> >>> cm, layer 28 will be at 54.737 and we will have 3528 wires. We pretty
> >>> much shifted things out by the 2.6 mm and picked up 28 channels.
> >>>
> >>> Unless people scream a lot, we would like to go with the first option
> >>> (3500 channels). The information on that is as given in the following.
> >>>
> >>> Curtis and Yves
> >>> --------------------------------------------------------------------------------------------------------
> >>>
> >>> Global Information:
> >>>
> >>> Tube radius: 0.801250
> >>> Instrumented Layers is 28
> >>> Instrumented Channels is 3500
> >>> layer number radius(center) radius(plate) stereo
> >>> $ 1$ & $ 42$ & $ 10.692$ & $ 10.692$ & $ 0.000$ & $ 10.692$ \\
> >>> $ 2$ & $ 42$ & $ 12.046$ & $ 12.046$ & $ 0.000$ & $ 1.354$ \\
> >>> $ 3$ & $ 54$ & $ 13.757$ & $ 13.757$ & $ 0.000$ & $ 1.711$ \\
> >>> $ 4$ & $ 54$ & $ 15.119$ & $ 15.119$ & $ 0.000$ & $ 1.362$ \\
> >>> $ 5$ & $ 66$ & $ 16.913$ & $ 18.659$ & $ 0.105$ & $ 1.794$ \\
> >>> $ 6$ & $ 66$ & $ 18.288$ & $ 20.176$ & $ 0.113$ & $ 1.375$ \\
> >>> $ 7$ & $ 79$ & $ 20.312$ & $ 21.787$ & $ 0.105$ & $ 2.024$ \\
> >>> $ 8$ & $ 79$ & $ 21.694$ & $ 23.270$ & $ 0.112$ & $ 1.383$ \\
> >>> $ 9$ & $ 92$ & $ 23.600$ & $ 24.882$ & $-0.105$ & $ 1.906$ \\
> >>> $10$ & $ 92$ & $ 24.982$ & $ 26.338$ & $-0.111$ & $ 1.382$ \\
> >>> $11$ & $105$ & $ 26.919$ & $ 28.049$ & $-0.105$ & $ 1.937$ \\
> >>> $12$ & $105$ & $ 28.302$ & $ 29.490$ & $-0.110$ & $ 1.383$ \\
> >>> $13$ & $122$ & $ 31.124$ & $ 31.124$ & $ 0.000$ & $ 2.822$ \\
> >>> $14$ & $122$ & $ 32.502$ & $ 32.502$ & $ 0.000$ & $ 1.378$ \\
> >>> $15$ & $134$ & $ 34.170$ & $ 34.170$ & $ 0.000$ & $ 1.668$ \\
> >>> $16$ & $134$ & $ 35.548$ & $ 35.548$ & $ 0.000$ & $ 1.378$ \\
> >>> $17$ & $145$ & $ 37.179$ & $ 38.006$ & $-0.105$ & $ 1.632$ \\
> >>> $18$ & $145$ & $ 38.566$ & $ 39.423$ & $-0.109$ & $ 1.386$ \\
> >>> $19$ & $157$ & $ 40.272$ & $ 41.036$ & $-0.105$ & $ 1.706$ \\
> >>> $20$ & $157$ & $ 41.660$ & $ 42.450$ & $-0.108$ & $ 1.388$ \\
> >>> $21$ & $169$ & $ 43.351$ & $ 44.062$ & $ 0.105$ & $ 1.691$ \\
> >>> $22$ & $169$ & $ 44.739$ & $ 45.473$ & $ 0.108$ & $ 1.388$ \\
> >>> $23$ & $181$ & $ 46.421$ & $ 47.086$ & $ 0.105$ & $ 1.682$ \\
> >>> $24$ & $181$ & $ 47.810$ & $ 48.494$ & $ 0.108$ & $ 1.389$ \\
> >>> $25$ & $196$ & $ 50.116$ & $ 50.116$ & $ 0.000$ & $ 2.306$ \\
> >>> $26$ & $196$ & $ 51.501$ & $ 51.501$ & $ 0.000$ & $ 1.385$ \\
> >>> $27$ & $208$ & $ 53.105$ & $ 53.105$ & $ 0.000$ & $ 1.605$ \\
> >>> $28$ & $208$ & $ 54.488$ & $ 54.488$ & $ 0.000$ & $ 1.383$ \\
> >>>
> >>>
> >>> ---------------------------------------------------------------------------------------------------------------
> >>>
> >>> First hole in each layer (length in centimeters) Upstream Endplate
> >>> (inside chamber) (outside chamber)
> >>> Lyr num dPhi r_c r_p x_p y_p z_p
> >>> x_p y_p z_p
> >>> 1 42 0.14960 10.6919 10.6919 ( 10.6919 0.0000 0.00 ) (
> >>> 10.6919 0.0000 -0.95 )
> >>> 2 42 0.14960 12.0460 12.0460 ( 12.0123 0.9002 0.00 ) (
> >>> 12.0123 0.9002 -0.95 )
> >>> 3 54 0.11636 13.7569 13.7569 ( 13.7470 0.5237 0.00 ) (
> >>> 13.7470 0.5237 -0.95 )
> >>> 4 54 0.11636 15.1191 15.1191 ( 15.0491 1.4530 0.00 ) (
> >>> 15.0491 1.4530 -0.95 )
> >>> 5 65 0.09666 16.7307 18.4941 ( 16.7307 7.8813 0.00 ) (
> >>> 16.7307 7.9814 -0.95 )
> >>> 6 65 0.09666 18.1112 20.0201 ( 17.6779 9.3967 0.00 ) (
> >>> 17.6726 9.5049 -0.95 )
> >>> 7 79 0.07953 20.2489 21.7286 ( 20.3732 7.5541 0.00 ) (
> >>> 20.3748 7.6542 -0.95 )
> >>> 8 79 0.07953 21.6272 23.2077 ( 21.4220 8.9270 0.00 ) (
> >>> 21.4195 9.0339 -0.95 )
> >>> 9 92 0.06830 23.5842 24.8663 ( 23.5842 -7.8813 0.00 ) (
> >>> 23.5842 -7.9814 -0.95 )
> >>> 10 92 0.06830 24.9651 26.3222 ( 25.2354 -7.4856 0.00 ) (
> >>> 25.2390 -7.5915 -0.95 )
> >>> 11 104 0.06042 26.8017 27.9365 ( 26.7313 -8.1169 0.00 ) (
> >>> 26.7304 -8.2170 -0.95 )
> >>> 12 104 0.06042 28.1916 29.3852 ( 28.3625 -7.6847 0.00 ) (
> >>> 28.3648 -7.7899 -0.95 )
> >>> 13 122 0.05150 31.2679 31.2679 ( 31.2662 -0.3247 0.00 ) (
> >>> 31.2662 -0.3247 -0.95 )
> >>> 14 122 0.05150 32.6520 32.6520 ( 32.6481 0.5017 0.00 ) (
> >>> 32.6481 0.5017 -0.95 )
> >>> 15 134 0.04689 34.2552 34.2552 ( 34.2544 0.2312 0.00 ) (
> >>> 34.2544 0.2312 -0.95 )
> >>> 16 134 0.04689 35.6366 35.6366 ( 35.6204 1.0758 0.00 ) (
> >>> 35.6204 1.0758 -0.95 )
> >>> 17 145 0.04333 37.2487 38.0733 ( 37.3593 -7.3388 0.00 ) (
> >>> 37.3608 -7.4389 -0.95 )
> >>> 18 145 0.04333 38.6376 39.4931 ( 38.9083 -6.7711 0.00 ) (
> >>> 38.9120 -6.8749 -0.95 )
> >>> 19 157 0.04002 40.3422 41.1049 ( 40.2962 -8.1133 0.00 ) (
> >>> 40.2957 -8.2134 -0.95 )
> >>> 20 157 0.04002 41.7323 42.5212 ( 41.8443 -7.5571 0.00 ) (
> >>> 41.8457 -7.6607 -0.95 )
> >>> 21 169 0.03718 43.4265 44.1359 ( 43.3664 8.2059 0.00 ) (
> >>> 43.3656 8.3060 -0.95 )
> >>> 22 169 0.03718 44.8172 45.5493 ( 44.5899 9.2992 0.00 ) (
> >>> 44.5872 9.4024 -0.95 )
> >>> 23 181 0.03471 46.4992 47.1624 ( 46.5878 7.3398 0.00 ) (
> >>> 46.5889 7.4399 -0.95 )
> >>> 24 181 0.03471 47.8901 48.5731 ( 47.8428 8.3910 0.00 ) (
> >>> 47.8422 8.4941 -0.95 )
> >>> 25 197 0.03189 50.4467 50.4467 ( 50.4439 -0.5335 0.00 ) (
> >>> 50.4439 -0.5335 -0.95 )
> >>> 26 197 0.03189 51.8336 51.8336 ( 51.8329 0.2784 0.00 ) (
> >>> 51.8329 0.2784 -0.95 )
> >>> 27 209 0.03006 53.4403 53.4403 ( 53.4393 0.3198 0.00 ) (
> >>> 53.4393 0.3198 -0.95 )
> >>> 28 209 0.03006 54.8255 54.8255 ( 54.8134 1.1521 0.00 ) (
> >>> 54.8134 1.1521 -0.95 )
> >>> First hole in each layer (length in centimeter) Downstream Endplate
> >>> (inside chamber) (outside chamber)
> >>> Lyr num dPhi r_c r_p x_p y_p z_p
> >>> x_p y_p z_p
> >>> 1 42 0.14960 10.6919 10.6919 ( 10.6919 0.0000 150.00 ) ( 10.6919
> >>> 0.0000 150.60 )
> >>> 2 42 0.14960 12.0460 12.0460 ( 12.0123 0.9002 150.00 ) ( 12.0123
> >>> 0.9002 150.60 )
> >>> 3 54 0.11636 13.7569 13.7569 ( 13.7470 0.5237 150.00 ) ( 13.7470
> >>> 0.5237 150.60 )
> >>> 4 54 0.11636 15.1191 15.1191 ( 15.0491 1.4530 150.00 ) ( 15.0491
> >>> 1.4530 150.60 )
> >>> 5 65 0.09666 16.7307 18.4941 ( 16.7307 -7.8813 150.00 ) ( 16.7307
> >>> -7.9444 150.60 )
> >>> 6 65 0.09666 18.1112 20.0201 ( 18.5023 -7.6467 150.00 ) ( 18.5056
> >>> -7.7148 150.60 )
> >>> 7 79 0.07953 20.2489 21.7286 ( 20.1193 -8.2065 150.00 ) ( 20.1183
> >>> -8.2695 150.60 )
> >>> 8 79 0.07953 21.6272 23.2077 ( 21.8203 -7.9039 150.00 ) ( 21.8219
> >>> -7.9712 150.60 )
> >>> 9 92 0.06830 23.5842 24.8663 ( 23.5842 7.8813 150.00 ) ( 23.5842
> >>> 7.9444 150.60 )
> >>> 10 92 0.06830 24.9651 26.3222 ( 24.6657 9.1903 150.00 ) ( 24.6635
> >>> 9.2570 150.60 )
> >>> 11 104 0.06042 26.8017 27.9365 ( 26.8700 7.6452 150.00 ) ( 26.8706
> >>> 7.7082 150.60 )
> >>> 12 104 0.06042 28.1916 29.3852 ( 28.0076 8.8916 150.00 ) ( 28.0062
> >>> 8.9579 150.60 )
> >>> 13 122 0.05150 31.2679 31.2679 ( 31.2662 -0.3247 150.00 ) ( 31.2662
> >>> -0.3247 150.60 )
> >>> 14 122 0.05150 32.6520 32.6520 ( 32.6481 0.5017 150.00 ) ( 32.6481
> >>> 0.5017 150.60 )
> >>> 15 134 0.04689 34.2552 34.2552 ( 34.2544 0.2312 150.00 ) ( 34.2544
> >>> 0.2312 150.60 )
> >>> 16 134 0.04689 35.6366 35.6366 ( 35.6204 1.0758 150.00 ) ( 35.6204
> >>> 1.0758 150.60 )
> >>> 17 145 0.04333 37.2487 38.0733 ( 37.1301 8.4222 150.00 ) ( 37.1292
> >>> 8.4852 150.60 )
> >>> 18 145 0.04333 38.6376 39.4931 ( 38.3164 9.5686 150.00 ) ( 38.3140
> >>> 9.6339 150.60 )
> >>> 19 157 0.04002 40.3422 41.1049 ( 40.3869 7.6491 150.00 ) ( 40.3873
> >>> 7.7121 150.60 )
> >>> 20 157 0.04002 41.7323 42.5212 ( 41.6118 8.7470 150.00 ) ( 41.6109
> >>> 8.8122 150.60 )
> >>> 21 169 0.03718 43.4265 44.1359 ( 43.4843 -7.5563 150.00 ) ( 43.4847
> >>> -7.6193 150.60 )
> >>> 22 169 0.03718 44.8172 45.5493 ( 45.0140 -6.9627 150.00 ) ( 45.0156
> >>> -7.0278 150.60 )
> >>> 23 181 0.03471 46.4992 47.1624 ( 46.4044 -8.4218 150.00 ) ( 46.4037
> >>> -8.4848 150.60 )
> >>> 24 181 0.03471 47.8901 48.5731 ( 47.9357 -7.8429 150.00 ) ( 47.9361
> >>> -7.9078 150.60 )
> >>> 25 197 0.03189 50.4467 50.4467 ( 50.4439 -0.5335 150.00 ) ( 50.4439
> >>> -0.5335 150.60 )
> >>> 26 197 0.03189 51.8336 51.8336 ( 51.8329 0.2784 150.00 ) ( 51.8329
> >>> 0.2784 150.60 )
> >>> 27 209 0.03006 53.4403 53.4403 ( 53.4393 0.3198 150.00 ) ( 53.4393
> >>> 0.3198 150.60 )
> >>> 28 209 0.03006 54.8255 54.8255 ( 54.8134 1.1521 150.00 ) ( 54.8134
> >>> 1.1521 150.60 )
> >>>
> >>>
> >>
> >>
>
>
--
Professor Curtis A. Meyer Department of Physics
Phone: (412) 268-2745 Carnegie Mellon University
Fax: (412) 681-0648 Pittsburgh PA 15213-3890
cmeyer@ernest.phys.cmu.edu http://www.curtismeyer.com/