[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: Change of Shipping address
Hall D Electronics:
Hi Mitch,
Oplesae ignore the excel file - all the info is in the word doc.
Cheers, Jim.
On 5/11/07 11:01 AM, "Mitch Newcomer" <mitch@hep.upenn.edu> wrote:
> Hall D Electronics:
>
> Jim, I'm not making any sense out of the attached excel file. Is it
> the right one?
>
> James Pinfold wrote:
>> Hi Fernando, Mitch, Elton,
>>
>> The plan we laid out is include in the attached document
>> That is the basis of the current funding for this project.
>> Please check section called "Revised Plan" which has the latest
>> version of the plan.
>>
>> We are over budget on this plan because of:
>> A) Greater than estimated charges for Mitch's student
>> B) Greater cost of the ASICs
>> C) etc.
>>
>> Also we are way behind the timeline envisaged in the plan.
>> This is because the development of the ASIC took longer than envisaged -
>> c'est la vie.
>>
>> In this plan Alberta's responsibility was in the development of the preamp
>> Card and in its testing. Of course this workd would have been carried out in
>> strong and close collaboration with the detectors groups concerned. Mitch of
>> course was going to do the acceptance testing. As we have Lars and Jan here
>> I believe this is still a realistic option although now we will be building
>> on a good first step. But perhaps we should discuss this.
>>
>> I suggest I talk to Lars Holm and we arrange a phone discussion on the
>> issues laid out above as well as Elton's question,
>> some time next week. If you agree could you send Lars & Jan your available
>> times.
>>
>> Cheers, Jim.
>>
>>
>>
>>
>>
>> On 5/11/07 7:24 AM, "Fernando J. Barbosa" <barbosa@jlab.org> wrote:
>>
>>
>>> Hi Elton,
>>>
>>> According to my email, no. Perhaps Elke can shine some light into
>>> the subject.
>>>
>>> Regards,
>>> Fernando
>>>
>>> Elton Smith wrote:
>>>
>>>> HI Fernando,
>>>>
>>>> I am a little confused. Will there be any testing at Alberta?
>>>>
>>>> Thanks, Elton.
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> Elton Smith
>>>> Jefferson Lab MS 12H5
>>>> 12000 Jefferson Ave
>>>> Suite # 16
>>>> Newport News, VA 23606
>>>> elton@jlab.org
>>>> (757) 269-7625
>>>>
>>>> On Thu, 10 May 2007, Fernando J. Barbosa wrote:
>>>>
>>>>
>>>>
>>>>> Hi Mitch,
>>>>>
>>>>> The BIS-711 export control form has been completed and faxed to Jim
>>>>> Cousins at MOSIS.
>>>>> The following is a tentative outline of the next steps:
>>>>>
>>>>> 1. The chips will be shipped to you for testing.
>>>>> 2. After testing, these will be shipped to Jlab to be assembled onto
>>>>> the preamp cards.
>>>>> 3. The preamp cards are being designed at Jlab for further tests on
>>>>> the prototype FDC and CDC wire chambers.
>>>>> 4. I will circulate a test spec sheet that we can use for qualifying
>>>>> the chips.
>>>>>
>>>>> Please let me know if there are other steps that need to be considered
>>>>> at this time.
>>>>>
>>>>> Best regards,
>>>>> Fernando
>>>>>
>>>>> Mitch Newcomer wrote:
>>>>>
>>>>>
>>>>>> Design 77419 (GAS-1)
>>>>>> Fab-ID is T74LAB
>>>>>> PO: 0000087100
>>>>>>
>>>>>> RE>>>>The project will be shipped to:
>>>>>> Dr. J. PINFOLD C/O SUZETTE CHAN
>>>>>> UNIV. OF ALBERTA CENTRAL RECEIVING
>>>>>> MATERIAL MGT. BUILDING CEB 445
>>>>>> 116 STREET & 85 AVENUE
>>>>>> EDMOND AB T6G 2R3
>>>>>>
>>>>>>
>>>>>> Please ship all 40 parts to the following US address:
>>>>>> Mitch Newcomer
>>>>>> University of Pennsylvania
>>>>>> 209 S 33rd St,
>>>>>> Philadelphia, PA 19104
>>>>>> These parts will be bench tested at Penn before assembly
>>>>>> on boards
>>>>>>
>>>>>> Mitch Newcomer.
>>>>>>
>>>>>>
>>>>>>
>>>>
>>>>