[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: Change of Shipping address
Hall D Electronics:
Jim, I'm not making any sense out of the attached excel file. Is it
the right one?
James Pinfold wrote:
> Hi Fernando, Mitch, Elton,
>
> The plan we laid out is include in the attached document
> That is the basis of the current funding for this project.
> Please check section called "Revised Plan" which has the latest
> version of the plan.
>
> We are over budget on this plan because of:
> A) Greater than estimated charges for Mitch's student
> B) Greater cost of the ASICs
> C) etc.
>
> Also we are way behind the timeline envisaged in the plan.
> This is because the development of the ASIC took longer than envisaged -
> c'est la vie.
>
> In this plan Alberta's responsibility was in the development of the preamp
> Card and in its testing. Of course this workd would have been carried out in
> strong and close collaboration with the detectors groups concerned. Mitch of
> course was going to do the acceptance testing. As we have Lars and Jan here
> I believe this is still a realistic option although now we will be building
> on a good first step. But perhaps we should discuss this.
>
> I suggest I talk to Lars Holm and we arrange a phone discussion on the
> issues laid out above as well as Elton's question,
> some time next week. If you agree could you send Lars & Jan your available
> times.
>
> Cheers, Jim.
>
>
>
>
>
> On 5/11/07 7:24 AM, "Fernando J. Barbosa" <barbosa@jlab.org> wrote:
>
>
>> Hi Elton,
>>
>> According to my email, no. Perhaps Elke can shine some light into
>> the subject.
>>
>> Regards,
>> Fernando
>>
>> Elton Smith wrote:
>>
>>> HI Fernando,
>>>
>>> I am a little confused. Will there be any testing at Alberta?
>>>
>>> Thanks, Elton.
>>>
>>>
>>>
>>>
>>>
>>>
>>> Elton Smith
>>> Jefferson Lab MS 12H5
>>> 12000 Jefferson Ave
>>> Suite # 16
>>> Newport News, VA 23606
>>> elton@jlab.org
>>> (757) 269-7625
>>>
>>> On Thu, 10 May 2007, Fernando J. Barbosa wrote:
>>>
>>>
>>>
>>>> Hi Mitch,
>>>>
>>>> The BIS-711 export control form has been completed and faxed to Jim
>>>> Cousins at MOSIS.
>>>> The following is a tentative outline of the next steps:
>>>>
>>>> 1. The chips will be shipped to you for testing.
>>>> 2. After testing, these will be shipped to Jlab to be assembled onto
>>>> the preamp cards.
>>>> 3. The preamp cards are being designed at Jlab for further tests on
>>>> the prototype FDC and CDC wire chambers.
>>>> 4. I will circulate a test spec sheet that we can use for qualifying
>>>> the chips.
>>>>
>>>> Please let me know if there are other steps that need to be considered
>>>> at this time.
>>>>
>>>> Best regards,
>>>> Fernando
>>>>
>>>> Mitch Newcomer wrote:
>>>>
>>>>
>>>>> Design 77419 (GAS-1)
>>>>> Fab-ID is T74LAB
>>>>> PO: 0000087100
>>>>>
>>>>> RE>>>>The project will be shipped to:
>>>>> Dr. J. PINFOLD C/O SUZETTE CHAN
>>>>> UNIV. OF ALBERTA CENTRAL RECEIVING
>>>>> MATERIAL MGT. BUILDING CEB 445
>>>>> 116 STREET & 85 AVENUE
>>>>> EDMOND AB T6G 2R3
>>>>>
>>>>>
>>>>> Please ship all 40 parts to the following US address:
>>>>> Mitch Newcomer
>>>>> University of Pennsylvania
>>>>> 209 S 33rd St,
>>>>> Philadelphia, PA 19104
>>>>> These parts will be bench tested at Penn before assembly
>>>>> on boards
>>>>>
>>>>> Mitch Newcomer.
>>>>>
>>>>>
>>>>>
>>>
>>>