[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: Collimator layout
On Wed, 21 May 2008, Elton Smith wrote:
Actually I think we need a side and a top view to have all dimensions
available easily. As we want to check this drawin than vs the Monte Carlo.
cheers elke
> Date: Wed, 21 May 2008 10:16:11 -0400 (EDT)
> From: Elton Smith <elton@jlab.org>
> To: Richard Jones <richard.t.jones@uconn.edu>
> Cc: Tim Whitlatch <whitey@jlab.org>,
> Hall D beam working group <halld-tagger@jlab.org>
> Subject: Re: Collimator layout
>
>
> HI Tim,
>
> On the drawing it would also be very useful to show the materials in each
> of the blocks. (Fe, concrete, Pb, etc).
>
> Thanks, Elton.
>
>
>
>
> Elton Smith
> Jefferson Lab MS 12H5
> 12000 Jefferson Ave
> Suite # 16
> Newport News, VA 23606
> elton@jlab.org
> (757) 269-7625
> (757) 269-6331 fax
>
> On Wed, 21 May 2008, Richard Jones wrote:
>
> > Tim,
> >
> > Here are some comments on the collimator cave layout views you sent me.
> > 1. The vacuum pipe that carries the photon beam from the tagger hall to the
> > collimator cave is shown as 5cm in diameter. The civil plans show a stainless
> > steel pipe 10 inches in diameter connecting the two halls. The simplest plan
> > would simply be to evacuate the entire 10 inch pipe (only rough vacuum is
> > required) in which case the pipe that enters the cave area should have a diameter
> > of 25.4cm.
> > 2. The primary collimator should be 30cm long. In the drawing it looks like only
> > 15cm.
> > 3. The pole gap in the first sweep magnet is nominally 2cm. This is not shown, and
> > is subject to change as we refine the specs on the sweeps.
> > 4. The hole through the 200cm iron shielding block is shown at 1cm dimensions. It
> > should be a 2cm x 2cm square hole.
> > 5. The hole through the 100cm x 200cm x 200cm concrete shielding block is shown at
> > 1cm dimensions. It should be a 2cm x 2cm square hole.
> > 6. The secondary collimator is shown as 25cm long, or so. The length in my geometry
> > is 50cm, with a circular bore hole diameter of 5mm.
> > 7. The inner dimensions of the cave area in my description were 270cm high x 450cm
> > wide. The lead wall separating the cave from the main hall area was designed
> > with dimensions 470cm x 270cm to completely cover the opening in the vertical
> > direction (270cm) and to go 10cm past the left and right inner wall dimensions.
> > This could be accomplished by a notch in the side walls at the entrance to the
> > cave.
> > Richard Jones
> >
> >
> > 1. Tim Whitlatch wrote:
> > Hi Richard,
> >
> > Slava has dimensioned the collimator layout as supplied in Igor's Autocad
> > file. There are many dimensions for the shielding sizes as well as the
> > beamline locations. Please look this over and let me know if this is what
> > is needed as far as locations and size. There is a top and side view .pdf
> > attached.
> >
> > Thanks,
> >
> > Tim
> >
> >
> >
> >
> >
>
>
( `,_' )+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=
) `\ -
/ '. | +
| `, Elke-Caroline Aschenauer =
\,_ `-/ -
,&&&&&V Jefferson Lab +
,&&&&&&&&: HALL-D 12C / F381 121-A Atlantic Avenue =
,&&&&&&&&&&; Suite 8 Hampton, VA 23664 -
| |&&&&&&&;\ 12000 Jefferson Ave +
| | :_) _ Newport News, VA 23606 Tel.: 001-757-224-1216 =
| | ;--' | Mail: elke@jlab.org Mobil: 001-757-256-5224 -
'--' `-.--. | +
\_ | |---' Tel.: 001-757-269-5352 =
`-._\__/ Fax.: 001-757-269-6331 -
+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+=-+